Correct operation method of double head hydraulic pipe bender
2018/11/13 13:22:41
The operation of double head hydraulic pipe bender needs to follow certain steps and methods. Don't randomly move the button to avoid unnecessary load on the machine. So how to operate is the right way? Next, let's give you a brief introduction in order.
1. For good grounding connection, automatic pipe bender must be used, and the cable shall not be less than 4mm2 copper cable. The power supply voltage cannot exceed the regular size. The plug cannot be inserted and pulled out. The control circuit cannot be tested with a megger, otherwise the equipment may be damaged.
2. When plugging in and out the connector, do not pull out the cable or cable to prevent the welding from falling off.
3. Switch on, switch off, encoder, etc. you can't hit it with a hard object.
4. Do not touch the HMI with sharp objects.
5. The electrical box and shall be placed in a ventilated place to prevent the action of dust and corrosive gas.
6. Unable to install privately and change to PC I / O.
7. Interchangeable automatic frequency multiplier power supply is necessary to identify the motor from the beginning.
8. The automatic pipe bender and must be kept clean, with special attention to the clamping block The sliding block and other sliding grooves shall be free of foreign matters.
9. Soft oil is added to chains and other sliding parts.
10. The power supply must be disconnected during cleaning and maintenance.
11. Preparation before driving: check whether the oil level of the fuel tank is horizontal. Add oil at each soft point, confirm the direction of the motor at the beginning, verify that the oil pump has one, check the abnormality of the hydraulic system and check the oil leakage after opening the machine (the encoder is not allowed to add oil);
12 pressure regulation: use solenoid valve to adjust the pressure and ensure that the system pressure reaches the required operating pressure, usually no more than 12.5mpa.
13. Setting the mold: the mold device, the mold and the clamping block must be in the center, the holding block can be adjusted with bolts, the backing block and mold are in the center, the reinforcing block is adjustable, the core and mold are in the center, and the head of the core is loose. Tighten the screws and tighten the screws during adjustment.
Zhangjiagang Yousheng Machinery Manufacturing Co., Ltd. is located in Zhangjiagang, a famous sanitary city in the south of the Yangtze River, with strong technical and economic foundation and convenient land and water transportation. The company manufactures ys-75nct / ys-89nct pipe bending machine series, ys-nc single head pipe bending machine series, ys-38nc double head hydraulic pipe bending machine, ys-cnc three-dimensional numerical control hydraulic pipe bending machine series, semi-automatic chamfering machine, double head hydraulic pipe bending machine, full-automatic double head pipe bending machine, large semi hollow rivet machine, cutting machine, circular saw machine, bending machine, metal round pipe, round bar chamfering machine, pipe end forming machine and other pipe profile processing machines. The products are widely used in shipbuilding, Automobile, motorcycle, bicycle, stroller, petrochemical industry, steel furniture and other pipe processing industries are ideal equipment for cutting, bending, shrinking, expanding and riveting of various pipe profiles. The sales network is all over the country, and the products are highly praised by users.
1. For good grounding connection, automatic pipe bender must be used, and the cable shall not be less than 4mm2 copper cable. The power supply voltage cannot exceed the regular size. The plug cannot be inserted and pulled out. The control circuit cannot be tested with a megger, otherwise the equipment may be damaged.
2. When plugging in and out the connector, do not pull out the cable or cable to prevent the welding from falling off.
3. Switch on, switch off, encoder, etc. you can't hit it with a hard object.
4. Do not touch the HMI with sharp objects.
5. The electrical box and shall be placed in a ventilated place to prevent the action of dust and corrosive gas.
6. Unable to install privately and change to PC I / O.
7. Interchangeable automatic frequency multiplier power supply is necessary to identify the motor from the beginning.
8. The automatic pipe bender and must be kept clean, with special attention to the clamping block The sliding block and other sliding grooves shall be free of foreign matters.
9. Soft oil is added to chains and other sliding parts.
10. The power supply must be disconnected during cleaning and maintenance.
11. Preparation before driving: check whether the oil level of the fuel tank is horizontal. Add oil at each soft point, confirm the direction of the motor at the beginning, verify that the oil pump has one, check the abnormality of the hydraulic system and check the oil leakage after opening the machine (the encoder is not allowed to add oil);
12 pressure regulation: use solenoid valve to adjust the pressure and ensure that the system pressure reaches the required operating pressure, usually no more than 12.5mpa.
13. Setting the mold: the mold device, the mold and the clamping block must be in the center, the holding block can be adjusted with bolts, the backing block and mold are in the center, the reinforcing block is adjustable, the core and mold are in the center, and the head of the core is loose. Tighten the screws and tighten the screws during adjustment.
Zhangjiagang Yousheng Machinery Manufacturing Co., Ltd. is located in Zhangjiagang, a famous sanitary city in the south of the Yangtze River, with strong technical and economic foundation and convenient land and water transportation. The company manufactures ys-75nct / ys-89nct pipe bending machine series, ys-nc single head pipe bending machine series, ys-38nc double head hydraulic pipe bending machine, ys-cnc three-dimensional numerical control hydraulic pipe bending machine series, semi-automatic chamfering machine, double head hydraulic pipe bending machine, full-automatic double head pipe bending machine, large semi hollow rivet machine, cutting machine, circular saw machine, bending machine, metal round pipe, round bar chamfering machine, pipe end forming machine and other pipe profile processing machines. The products are widely used in shipbuilding, Automobile, motorcycle, bicycle, stroller, petrochemical industry, steel furniture and other pipe processing industries are ideal equipment for cutting, bending, shrinking, expanding and riveting of various pipe profiles. The sales network is all over the country, and the products are highly praised by users.